Your Chain Maker Publishes A Filing Angle. Now You Can Actually Set It.
Sharpen to your chain's angle, not the tool's. It isn't your saw and it isn't your technique. It's The 30-Degree Default: every clamp-on sharpener on the shelf is drilled to one fixed angle, so whatever your chain's maker specified, the tool grinds 30 degrees and your cutters get reshaped instead of resharpened. The AngleSet puts a graduated dial where that fixed hole used to be. You set the angle, clamp it to the bar, and turn the crank. Try it for 90 days; if it doesn't earn its place in your kit, send it back.
- ✓Match your chain's own filing angle — a graduated dial swings the guide seat across 0 to 30 degrees on either side of centre
- ✓Leave the chain on the saw — the jig clamps straight onto the guide bar, so nothing gets dismantled, re-tensioned or lost in the grass
- ✓Crank it by hand or chuck it in a drill — the same diamond burr fits both, so you pick speed or silence
- ✓Do both cutter directions without lifting it off — the guide seat swings across and re-sets, and the two halves of the chain end up matched
- ✓Sharpen where the work is — no cord, no battery and nothing to charge, so a dead saw never ends the afternoon
- ✓Stop replacing chains that still had life in them — one tool you own instead of a sharpening bill that never stops
Set the dial to 25 for my ripping chain, worked through the loop in about twenty minutes, and the next cut threw proper chips instead of dust. — Dale W., Verified Buyer
Watch The Dial Do The Work.
Seeing it once is enough. The jig goes onto a bar in the driveway with the chain still on the saw. The dial gets set against a cutter before a single tooth is touched. Then the same burr goes into a cordless drill on the bench for the chain that has been sitting dull since spring. Built around the filing spec the chain makers publish, not around one hole drilled at a factory.
One Moving Part Your Old Sharpener Doesn't Have
Everything else in this category clamps, guides and cranks the same way. The difference sits under the guide seat.
The Angle Dial
A chrome protractor sits under the guide seat, graduated across 0 to 30 degrees on both sides with fine ticks between. Loosen the thumb screw, swing the seat until the burr matches your cutter, or until it reads the figure your chain's maker publishes, and lock it there. Because the angle is finally yours to pick, The 30-Degree Default stops deciding how your chain cuts.
“My hardwood chain is specced at 25 and my crosscut at 30. This is the first jig I've owned that can tell the difference.” — Marcus T.
Clamps To The Bar
Two knurled thumb screws pull the body down onto the guide bar and the chain stays exactly where it is. Because nothing comes apart, there is no tension to reset, no drive link to fish out of the leaves, and no reason to put the job off until the weekend.
“Fifteen minutes from noticing it was dull to being back in the cut. Nothing came off the saw.” — Wayne B.
Crank Or Drill
The diamond burr threads into the crank arm for hand work, and the same burr drops into a cordless drill or rotary tool when there is a stack of chains waiting. Because you are not tied to a motor, a flat battery never ends the job, and a spare battery makes it quick.
“Crank out at the fence line, drill on the bench at home. Same tool, same burrs.” — Rick D.
Both Sides, No Flipping
Run the left-hand cutters, then swing the guide seat across, set the matching angle and run the right-hand ones. Because the tool never leaves the bar between sides, the two halves of the chain end up matched, which is what stops a saw wandering off the line you aimed it at.
“I used to end up with one side keener than the other and the cut would curve. It tracks straight now.” — Glen P.
Why One-Angle Sharpeners Leave Half Your Chains Wrong
Every clamp-on jig on the shelf is drilled to a single angle. The 30-Degree Default is fine for the one chain that happens to want 30 degrees, and wrong for every other chain you own.
Folgarden AngleSet
One-Angle Sharpeners
Six Places A Sharp Chain Changes The Day
Every Number, Before You Ask
What's in the Box:
1x AngleSet sharpener body · 1x crank handle · 5x diamond grinding burrs · 1x open-end wrench · 2x M6 lock nuts · 1x instruction sheet
Specs:
guarantee
Try it for 90 days. If you aren't completely satisfied, we'll refund every penny. No questions asked.
What Chainsaw Owners Say After The First Chain
1,284+ customers
Questions? Answered.
Set The Angle Before The Next Cut
Join 1,284+ owners who stopped grinding every chain to the same angle. Most people end up with one on the bench and one in the truck box. This sale ends soon and stock is running low.
Order Now & Save 50%